Mobile Electronics BODAS Sensors As a component of the BODAS system, the sensors supply the controller with important machine and environment information. Sensors for mobile equipment must be able to withstand extreme ambient loads, particularly if installed near the hydraulic power packs and engines. The sensors for different measured variables are based on robust, fail-safe, usually contactless measurement principles. The sensor elements are reliably integrated in suitable cases where they are protected against vibrations, impacts and harmful fluids, and are equipped with cables or plug connectors suitable for mobile use. Data Sheet (PDF) RE 95 130 Model ID Inductive speed sensor for frequency proportional speed measurement Key Features: No external voltage supply required Easy to install with fixed lengths of thread engagement ensured by hydraulic motor spacer rings Sealing surface ensures good O-ring seal Learn more about the ID Inductive Speed Sensor (PDF). Data Sheet (PDF) RE 95 132 Model DSM Hall-effect sensor for contactless speed measurement Key Features: Rotary direction detection Diagnostic signals Critical air gap Critical installation position Detects even low speeds Specially developed for the tough requirements of mobile applications Get more information on the DSM Speed Sensor (PDF). Data Sheet (PDF) RE 95 133 Model DSA Hall-effect sensor for contactless speed measurement Key Features: Due to its compact, sturdy design, the sensor is suitable for integrated use with Rexroth axial piston units. Detects even very low speeds Find out more about the DSA Speed Sensor (PDF). Data Sheet (PDF) RE 95 135 Model HDD Hall-effect dual sensor for contactless speed measurement Key Features: Easy installation without adjustment Detects even low speeds Large temperature range Protection against Short-circuit, reverse polarity protection Pressure-resistant sensor measuring surface High type of protection IP69k Available in a set with A2FM and A6VM/E axial piston motors Get more HDD Hall-Effect Speed Sensor (PDF) information. Data Sheet (PDF) RE 95 138 Model PR2 Thin film technology sensor to measurement pressure Key Features: Measurement range to 50, 160, 250, 400, 600 bar Shock and vibration resistant Type of protection IP67 to IP69K Ratiometric output signal 0.5..4.5V @ 5V Additional versions upon request Find out more about the PR2 Sensor (PDF). Data Sheet (PDF) RA 95 140 Model WS1 Angle of rotation sensor Key Features: Hall-effect semiconductor elements and integrated amplifiers Robust plastic housing with molded plug Metal inner housing and line filter for high electromagnetic compatibility Guide lever with fixing hole Find out more about the WS1 Angle of Rotation Sensor (PDF). Data Sheet (PDF) RE 95 143 Model AN2 Hall-effect sensor for angular measurement (Electronic-hydraulic hitch control EHR) Key Features: Angle sensor element based on Hall-effect principle Shaft can be turned through mechanically Integrated electronics with temperature compensation Output signal is ratiometrically proportional to angle Precise balance adjustment for zero point and sensitivity Get additional information on the AN2 Angle Sensor (PDF). Data Sheet (PDF) RE 95 145 Model TS Switch to monitor the temperature within a hydraulic circuit. Key Features: Single pole ON switch operates when temperature rises Plated flat pin connectors 6.3 mm x 0.8 mm Download more information on the TS Temperature Switch (PDF). Data Sheet (PDF) RE 95 148 Model VS Contamination switch for detecting metallic impurities in oil Key Features: VS is screwed into the existing bores (e.g. case drain ports) of hydraulic pumps and hydraulic motors. Available as integrated plug connector with mating plug or a free plug connector on the end of a connecting lead with two strands and a protective sheath. Learn more about the VS Contamination Switch (PDF). Data Sheet (PDF) RE 95 160 Model PO1 Inductive sensor for position measurement Key Features: Axially moving button with spring preload Inductive position sensor element according to differential throttle measuring principle Integrated electronics with temperature compensation Output signal is ratiometric and proportional to position Zero-point and sensitivity matched Get more information about the PO1 Inductive Position Sensor (PDF). Data Sheet (PDF) RE 95 166 Model INC BODAS Inclination Sensor Key Features: 2 axes inclination sensor High resolution and accuracy Current interface Type of protection IP67 Discover more about the INC Inclination Sensor(PDF). Data Sheet (PDF) RE 95 170 Model KMB Sensor for force measurement Key Features: Draft sensor follows Category 3 rear three-point linkage (ISO 730-1) Integrated electronics Ratiometric output signal proportional to force Zero point and sensitivity are calibrated Learn more about the KMB Force Sensor (PDF). Data Sheet (PDF) RE 95 180 Model TSF Temperature sensor for fluid Key Features: Monitors coolants, hydraulic oil or motor oil in vehicles Learn more about the TSF Fluid Temperature Sensor (PDF). Data Sheet (PDF) RE 95 181 Model TSA Temperature sensor for air Key Features: Monitors both ambient air and charge air temperature of ambient air in motor vehicles Find out more about the TSA Air Temperature Sensor (PDF). Contact us and find the BODAS sensor that’s ideally suited for your application.